Ask Electronics

Imo if your audience does know how to properly short two things, or solder then you're targeting the wrong audience or they need to learn some basic skills. Disclaimer everything but someone will blame you regardless

Maybe the people around me are more handy than the average but soldering irons are a common tool. Maybe if your target audience asks around they can borrow one.

If i didn't have a soldering iron, I'd probably grab a diode or resistor leg, snip it just enough to bridge the gap, press it down on the contacts, use super glue to hold it in place on both sides and the middle until it held and hope the glue doesn't block the contacts.

But this is an extremely shoddy solution and i doubt it will last long. You have to hold it firmly in place or the glue will get underneath the component leg. The user can't let it roll around under the finger. I suggest pressing it against the upper side of the contacts in the picture for leverage. Try it out yourself and see if you can do it. Once you verify with a multimeter you get current through, you can apply more super glue on top between the contacts to give it a little more grip, that may make it hold on for longer. Since it's for a low current application I'm betting just the contact surface of the component leg with the solder blobs underneath will be enough and will not overheat, but i would suggest letting it run a bit just to make sure. You can always make it just a smidge longer in order for the component leg to wrap around the blobs to increase the contact surface, in sort of a C shape.

A soldering iron for students can be pretty cheap and I'm only suggesting this alternative so you have some sort of low cost solution that doesn't involve one. Any diode or resistor will do, really, for like 5 cents and superglue for like 2/3€. Or if you want to put it in a kit just send small snips of tin plated, copper clad steel wire, but depending on how many kits you are manufacturing, it might be more cost effective just to use resistor/diode legs harvested from stuff you've got lying around.

Looks like a basic soldering job, give it a touch with resin and fresh solder and create a blob. Even my non-technical grandpa (in his 30s, he needed his 3yo daughter to operate a cassette deck for him!) had a soldering iron for some reason in his shack, and it's a good skill to have.

I'd need measurements or a better picture but it looks like they might be connected to adjacent pins (3 and 4, where 1 is on the right side from our POV) on the FFC connector. I would try to target that first, there are several options if that is available:

• wrapping both in a loop of thin wire
• wedging a metal item or piece of pencil lead in between (could damage the connector by bending pins if it gets reopened, or the item could dislocate)
• adding a thin strip of conductive foil to the cable's pins before plugging it in
• on the less-fragile flat cables that use real copper or aluminum strips, the insulation can be reliably removed on the traces in question using gentle force, and then the exposed conductors could be bridged with aluminum foil pressed against the cable by a paperclip, then taped over to prevent accidental shorts. Works with non-adjacent pins too, and can be used on PCBs if you can remove the solder mask on traces near board edges.

Speaking of the last method, you might not need a board edge nearby if you can rely on pressure from the device's housing:

1. Use a knife to gently scrape the solder mask off the traces in question, preferably far from any components.
2. Cut a piece of aluminum foil into a shape just big enough to cover both pads.
3. Use transparent tape to stick it to the board at the right spot.
4. Find or make a foam pad (or similar) of appropriate thickness (which can be determined using modeling clay) to place between the PCB and the housing/bracket/screw. You can use tape to keep it at the spot while reassembling the device.

If applicable, remind them that when screwing screws back into plastic, it is necessary to twist counterclockwise first to locate the original thread and not make a new one, which could ruin it.

Any metallic conductive epoxies out there. JB Weld or such

Only need a very tiny well placed drop

pencil, graphite is conductive.

I can't tell for sure, but it looks like you're bridging two traces that are connected to the center pin of Q17 (S1H6A) and either the "V" or "D" terminal of the XK ribbon connector with the designators marked "GVDCVG." perhaps you could use a very small wire between these points. If the V/D connection is actually V and V is for voltage, you can likely find other more convenient places to source a similar voltage around wherever the regulator circuitry for that voltage block is placed on the board.

Spit.

Eat some chips first so it’s a little salty.

Design a plastic housing for the connector that puts pressure on short while the ribbon is plugged in. Put a short in the plastic housing.

Making some assumptions here but…

You can get conductive adhesives but it would probably be cheaper to just include a soldering iron in the kit... I'm not sure I would be confident in getting good contact with self adhesive metal tape, your best option there is to probably get a small amount and experiment.

Hold a small piece of metal (paper clip?) between solder pads with a tweezer. Heat up tip of a metal fork/spoon (Sharp edge of fork could work better) on a stove. Take it from stove and use it immediately to melt the solder on one pad (seems like there is already enough solder there). I am not sure if it would work but maybe worth trying. Heating entire fork could be hard, so maybe something with smaller metal mass could work better, like a screwdriver, nail clipper etc).

Solder is really the only good method. With tape, the adhesive is going to give you really poor contact. With anything else you're going to struggle to keep whatever you are using to short those pads in place.

A thin wire attached to some tape placed perfectly to short them?

Clip a piece of a copper coin? Tape it down

Screwdriver