OrangeCorvus

Built a small machine using an Asrock N100DC-ITX motherboard, it has an Intel N100 built in and I also have 1x NVMe and 2x HDDs. The board has a DC Jack so no external PSU.

First time I booted it, the NVMe had Opensuse on it so I played around a little, no problem. When I boot into BIOS also no problem.

When I boot into Unraid, there is a strange sound coming from the back of the board, sounds like an interference sound. I cannot tell if it's coming from the ethernet port or from the power DC Jack. I think it's from the power.

I recorded it with my phone and bumped the sound +20 dB, this is how it sounds like. You can hear the fans and that sound. https://soundcloud.com/user-300866676-719653331/n100-1

https://soundcloud.com/user-300866676-719653331/n1002

For power I tried using both an Intel NUC 65w power adapter and an Asus laptop 90w power adapter, the one Asrock recommends on their website. The system has been running for 1-2days, with 4 containers and Home Assistant VM, it idles at around 16w. Without Home Assistant, it drops to 11w.

Any idea what that sound is?

Edit 1: If I go into BIOS and turn off Intel Turbo Boost Technology then it is silent but also kills my performance?

Edit 2 So because I did not want to leave Turbo Boost on, I did some more digging and also realized my CPU was always boosting in Unraid. using "watch grep "cpu MHz" /proc/cpuinfo" it was almost always between 2900Mhz and 3300Mhz. I installed Tip and Tweaks plugin and set Normal CPU Scaling Governor to power saver. The sound is gone and now it seems the CPU goes all the way down to 600 MHz and up to 3400MHz depending if it needs it. I don't know if the power saver will affect performance in any way but so far so good and I don't have hear that wheeeeee anymore.

The Asrock N100DC-ITX uses a 19v power brick so no separate PSU to power the drives. It comes with a 4 pin cable that splits into 2 SATA power.

The case I chose, Silverstone SG13, comes with a 3.5" HDD bracket but you need to mount the drive belly up so you can screw it in. The second drive I want to put where the PCIe slot is, found a nice 3d model for that. The thing is, the power cable would be too short and the drives would be too far apart to reach both.

So I removed the HDD bracket and cut 2 L-shaped aluminum stripes and I screwed the drive belly down. This way the cable now reaches both drives. I know, I could have cut the cable and made it longer but I prefer to avoid playing with power cables if I can.

Turned out quite good. Wanted to share it with other people. Now I need to find someone to 3d print the PCIe HDD holder and find some rubber stuff to put under the L-shapes to dampen the sound of the drive. This is the 3d model, https://www.printables.com/model/385403-pci-slot-hdd-bracket but V2 with the nice feet.

PS the drives in the images are broken so I just used them as dummy drives.

That's about it.

Linux Noob here

The Nuc is sitting under my TV and my wife uses it mostly to watch reality tv shows, cooking shows, etc on different websites. The requirement was for the Nuc to go to sleep after 30minutes of inactivity and to wake it up with the keyboard.

It had Leap 15.3 so I wanted to upgrade it but I managed to botch the upgrade. I decided to go with Debian instead, installed it, configured everything and when I handed it over to my wife I realized the Nuc never woke from sleep. Then I remember I had this problem in the past with it when I tried a whole bunch of distros and none of them managed to wake it up. I also read on Intel forums where people complained about the same issue with different Nucs and I think the general consensus was that it's a problem with the Nucs and it can't be solved.

What happens is, when the Nuc is sleeping, the power LED slowly blinks. When you wake it up, the LED goes completely away, like it's turned off but you can hear the fan is starting to spin. However, you don't have any image and you have to hold the power button a lot longer to turn if off, like it soft-resets.

So I nuked Debian, installed Leap 15.5 and it wakes from sleep without any issues. I am happy that it does and I like Opensuse but I have no idea what it does different compared to other distros in this regard.

Had an exchange of emails with someone, around 4-5 back and forth emails. He then told me that my last reply never arrived. When I forwarded that email again to him, he told me that actually the original reply arrived but landed in spam... he checked it after I forwarded the initial reply.

It's not critical or even a super important conversation but I think he lied to me. Is there any chance that a reply lands in spam if the last 4 mails in a thread arrived without a problem?

The emails were sent from a custom domain, using Office 365 Business. I have that email address for more than 6 years and I never had a problem with my emails landing in spam or never arriving. It's the first time I am hearing about it but I think he is duping me.

Edit Thanks all for the replies, it's good to know that it can happen.

Linux noob here. Usually in Windows if I have a 1TB SSD, I make a 250GB partition for Windows and all of its things and I use the rest for a second partition where I install my stuff and store my files.

Usually in case Windows decides to go belly up, I still have my files. In more than 20 years it has never happened but I've always done it like that. I mean if Windows goes bad, I can still remove the drive and insert it into a different PC and copy my files away.

Should I shrink Partition 3 and make another one? Or keep it as it is? If I would, I read that I need to boot with a live usb to be able to shrink it. What kind of partition would I make?

It's incredible how much the prices have fallen and that's how it should be. Sure, I bought the 960 close to launch but still the difference is staggering.

The 960 Evo still chugs along albeit it's a new one because a few months after I bought it, I had to RMA it. I guess that's what happens when you are an early adopter. I lost a few hours of work when the original 960 Evo decided to stop working but it also taught me to be more paranoia with backups.

cross-posted from: https://lemmy.world/post/469632

Looking to upgrade my Synology DS218+ to a 4 or 5 bay NAS because I am running out of storage. These past few days, I saw everybody and their mother say you cannot edit on anything else than a 10gig ethernet.

At the moment I am editing stuff from my workstation(AMD 5800x, 3060TI, 64GB, 1TB NVME) and I was curios how much worse would the experience be if I tried to edit from the NAS via my 1gig ethernet.

Most of my work is shot in 4k 150MBps and some even in 1080p.

So I copied around 5gigs of footage to my main NVME and the same footage on my NAS. First I added the NVME footage in a 4k timeline, chopped it up a little, threw 5 random LUTs, threw a noise reduction node and a camera shake effect. Playback in the edit page was ok, my GPU was gasping for air but playback was smooth. I rendered it at 16MBps and it came out in 5:22minutes.

Next, I deleted that footage, emptied cache and added the same clips from the NAS with the same cuts, LUTS and noise reduction. Playback was also super smooth and it rendered in 5:23minutes, so 1 second slower. That must be why everyone says you need 10GbE.

During all this time I had the Synology resource monitor on and it jumped at 30MBps at most.

So no real difference between the two. Next I took around 50gigs of footage and threw it on the same timeline, stacked it 4-5 times and indeed it was slow but it was because Davinci was caching stuff, when it finished the playback was super smooth.

All the time, proxies were disabled so the PC had to do all the work, if I add proxies it's a breeze.

I think that's where the difference comes in, Davinci is caching the clips and it doesn't really constantly read the original files.

I'm not saying you don't need more than 1gig, especially if you have more people working at the same time. If you work with RAW footage or footage that's 400MBps and up but the videos and posts I saw made it seem like even if you edit phone videos, 10GbE is a must....

Not a scientific test but I was super surprised to see that it made no difference if I was editing locally or from my NAS.

https://lemmy.world/c/indiegaming

!indiegaming@lemmy.world

Indie Gaming

I was just browsing the main page and opening different posts, any idea why Bitdefender thinks some pages are suspicious?

The first one with the infected, I think it was a post and it had some pictures, didn't click on anything, just loaded the post.