You're not going to see similar power levels to those ARM devices. A massive part will be the drives, 3.5" drives take between 6 and 10W per drive while running.
Do also have a n100 processor running proxmox with 3 VM. Can't try right now but can come back in a few days to let you know how much power it draws
Thanks that would be cool. Also if you can tell me if this is a NUC or something larger.
I'm not the other user, but this is my NUC running proxmox with 2 VMs and 2 LXCs. Running with an old i3, 16gb ram and a single 1tb NVME, no mechanical HDDs, and a few USB peripherals like a ZigBee dongle.
Wow, 7 watts. Nuts!
What IS that thing?
I'm running a n100 16gb with a 256ssd, 4vms and 4 docker images, it's pulling 7-9w.
Thanks, this is really efficient. I now have good hopes that changing my PSU should bring me closer to this
You still won't see that low of power consumption when you have something custom built.
With that being said you have a lot of room for improvement
It's literally one of those little known brand nuc, tiny box - beelink I think. Total cost $200 or so - it's been running non stop for the last 3 months without an issue. I don't think it even has a fan in there.
Curious, might have same machine but do consume a bit more, do you have one SSD + one nvme?
Sorry, I must have been too tired, got nearly all details wrong: 32GB RAM 1TB M.2, USB3.2, BT4.2,WiFi 5,4k HDMI, Gigabit Port, and not a Beelink but a DreamQuest. There's just the M2 interface disk connected, no SSD.
So pc is consuming 13W, this is with one nvme + one SSD, pic at 30w for a few seconds at boot.
Thanks for reporting!
Monitor CPU usage and frequencies to ensure CPU is throttling down properly. Then start unplugging hard drives, ram, nic cable to see how they affect power usage. Servethehome shows an N305 idling around 10w in a minipc without HDDs.
See if you can set the max power of the CPU in the BIOS.
It’s really strange for an N100 system to be drawing that much power, so maybe you have some really hungry SSDs or HDDs.
you can also do this in the OS, depending on your hardware it might be more reliable.
I have checked but I haven’t seen anything about power. By any chances, do you know in what category it may be?
I don’t know. I think that would depend on the BIOS.
it depends on the operating system you are using
For power consumption, NVMe drives use quite a lot of power, especially PCIe 4.0 ones. About 5W each during use.
3.5" HDD (especially 7200rpm or more) also consume significantly more than 2.5" 5400rpm HDDs that are optimized for low power (the latter use about 1W during use).
SATA SSDs fall somewhere in the middle.
Thanks. So If I take 5W a disk, I may have 20W just from the disks.
There are still 25W remaining. For a low power CPU that looks like a lot 😕
I never really tested it with 3.5" HDDs, but a google search makes it sound like they might be closer to 10W each.
My guess would be 25W from disks, 10W from CPU+RAM+MBO and 10W waste from PSU. Just a guess as I said
How does that work out in terms of energy consumption though?
If NVMe is at least 10x faster, but consumes 5x more power, it will use less energy to read or write the same amount of data overall.
To answer that question one would need to dive deeply into idle vs. in active use power consumption. It's not like a NAS gets turned off when not in use.
My server use about the same power no matter if its idle or under full load, so I dont think drive speed makes any difference. My SSDs use much less than my HDD anyway
Another way of reducing your overall power consumption: Do you need a NAS to be on 24/7?
My NAS is a NAS - just storage. It comes on and spins the 5x HDDs for a few hours in the day then shuts down. It's a NAS, I don't need to access my files at night when I'm asleep.
My VM host is a low power box with passive cooling which uses a SSD and runs my (mostly idle) VMs 24/7 for a few Watts.
So, maybe splitting up your requirements might save some power?
I planned to share it with my family. As I won’t be the only user, this is not ideal. Besides I run automatic backup and planned to also store them in the NAS. So again if it’s off half the time, this is not ideal.
Is that 45w a continuous draw, or is that from something that measured it while booting?
I have a small form factor Dell Optiplex with 1 NVME for the OS (Proxmox), and 3 drives (2.5" spinning disk), that idles at 10-20w. Running VM's pushes that up to 40-50w.
And that's still about 60-70w less than the desktop I've been running as a file server!
Unfortunately this is idling after boot. While booting it jumps to 70W and I haven’t seen it go below 45W idling…
Guess it's time to disconnect some hardware and test power consumption.
What kind of PSU are you using?
I’m using an EVGA 500 W1
EVGA 500 W1
That is a 500W PSU, no? That is vastly oversized and therefore inefficient for low power applications.
A place to share alternatives to popular online services that can be self-hosted without giving up privacy or locking you into a service you don't control.
Rules:
Be civil: we're here to support and learn from one another. Insults won't be tolerated. Flame wars are frowned upon.
No spam posting.
Posts have to be centered around self-hosting. There are other communities for discussing hardware or home computing. If it's not obvious why your post topic revolves around selfhosting, please include details to make it clear.
Don't duplicate the full text of your blog or github here. Just post the link for folks to click.
Submission headline should match the article title (don’t cherry-pick information from the title to fit your agenda).
No trolling.
Resources:
Any issues on the community? Report it using the report flag.
Questions? DM the mods!