this post was submitted on 14 Dec 2024
932 points (98.0% liked)
Lemmy Shitpost
27156 readers
3176 users here now
Welcome to Lemmy Shitpost. Here you can shitpost to your hearts content.
Anything and everything goes. Memes, Jokes, Vents and Banter. Though we still have to comply with lemmy.world instance rules. So behave!
Rules:
1. Be Respectful
Refrain from using harmful language pertaining to a protected characteristic: e.g. race, gender, sexuality, disability or religion.
Refrain from being argumentative when responding or commenting to posts/replies. Personal attacks are not welcome here.
...
2. No Illegal Content
Content that violates the law. Any post/comment found to be in breach of common law will be removed and given to the authorities if required.
That means:
-No promoting violence/threats against any individuals
-No CSA content or Revenge Porn
-No sharing private/personal information (Doxxing)
...
3. No Spam
Posting the same post, no matter the intent is against the rules.
-If you have posted content, please refrain from re-posting said content within this community.
-Do not spam posts with intent to harass, annoy, bully, advertise, scam or harm this community.
-No posting Scams/Advertisements/Phishing Links/IP Grabbers
-No Bots, Bots will be banned from the community.
...
4. No Porn/Explicit
Content
-Do not post explicit content. Lemmy.World is not the instance for NSFW content.
-Do not post Gore or Shock Content.
...
5. No Enciting Harassment,
Brigading, Doxxing or Witch Hunts
-Do not Brigade other Communities
-No calls to action against other communities/users within Lemmy or outside of Lemmy.
-No Witch Hunts against users/communities.
-No content that harasses members within or outside of the community.
...
6. NSFW should be behind NSFW tags.
-Content that is NSFW should be behind NSFW tags.
-Content that might be distressing should be kept behind NSFW tags.
...
If you see content that is a breach of the rules, please flag and report the comment and a moderator will take action where they can.
Also check out:
Partnered Communities:
1.Memes
10.LinuxMemes (Linux themed memes)
Reach out to
All communities included on the sidebar are to be made in compliance with the instance rules. Striker
founded 2 years ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
There are at least 3 standards for the + shape already. Phillips, Pozidrive, and Japanese Industrial Standard (JIS). They do not play well together.
insert obligatory xkcd standards reference
Don't forget Frearson/Reed & Prince!
But wait, there's more!
And even more!
We only have standards so we can break'em.
JIS has been obsoleted and replaced in Japanese products with the ISO Phillips bit shape. It still exists on lots of products pre 2000 though.
Kawasaki is still holding on strong to JIS screws in it's machinery.
Are you sure they're JIS? Because JIS and ISO are interchangeable and effectively the same; the ISO adopted standard used most of JIS's rules.
Yeah. I keep one of these around just for older Yamaha and newer Kawasaki equipment. You'll end up drilling half of them out if you try to use #3 ISO.
I'm in the powersports/agricultural industry, so we tend to lag behind everyone else.
That's just galvanic corrosion from using cadmium plated bolts in aluminum fuel injection hardware. It's basically free loctite.
JIS is looking better according to these guys…
This bugs me so much more than it should. Why do we have three different standards for + shaped screws? You know what doesn't have this problem? Flatheads. There's exactly one way to make a flathead screwdriver, and I won't be looking it up to make sure I'm right
I see that multiple people have replied, but unfortunately reading these comments would be a form of research so I must decline
Should the slot be partial or go all the way through? If partial, is that standard for the size of the screw, or universal?
How wide should the slot be? Should that change based on the size of the screw?
How deep should the slot be?
Should the sides of the slot be perfectly straight, or angled to perfectly fit the wedge shape of the driver? If angled, what angle?
Should the bottom of the slot be perfectly flat or slightly rounded so a coin or something could be used in a pinch? If rounded, what radius?
Should the top of the screw be perfectly flat, or domed, or raised?
Should the bottom of the head be flat, angled (at which angle), smooth, rough.
Should we use metric or freedom units for the thread pitch?
Should the threads go all the way to the head?
Should the point of the screw be flat or tapered (at what angle)?
Ok, only the first half of those were about the driver used, but I'm sure there are things I missed in that!
Their isn’t one way to make a flat head screwdriver. Some a chisel and some are slots. The slotted ones are better but more expensive.
Both still slip from the screw and are a pain to manually screw (slotted less so).
Pozi is the best + type screw. It’s pretty much standard for UK construction. The only time a different type is used is sometimes Phillips for plaster board or external hex and internal torx for long or large screws.