this post was submitted on 04 Oct 2023
12 points (92.9% liked)

homeassistant

12055 readers
40 users here now

Home Assistant is open source home automation that puts local control and privacy first. Powered by a worldwide community of tinkerers and DIY enthusiasts. Perfect to run on a Raspberry Pi or a local server. Available for free at home-assistant.io

founded 1 year ago
MODERATORS
 

First the layout. My garage is setup similar to this one, although mine is attached, has three light fixtures, and my driveway is 4 cars wide.

The wife wants me to replace the three basic on / off fixtures that we have (they're getting rusty) and keep them all matching. If I'm going to do this I want to add a camera to the setup.

Functionally I'd like the lights to have or work like they have dual bright capability where they come on full bright at sunset then after a couple of hours they dim down unless they detect motion. If they detect motion then they come back to full bright for a period of time then dim back down again. They do this for a set period of hours, say 4, then they turn off completely unless they detect motion.

My current lights are already automated for on / off (but not dimming or motion) through the use of HA and a z-wave switch.

Where I'm getting stuck is that I can see at least three ways to do this but none of them are perfect.

  1. Replace my dumb carriage fixtures with new dumb fixtures then change the switch to a dimming version plus add a motion sensor and camera out front. Then setup HA for the functionality I want. The upside of doing it this way is that it's very easy to get matching fixtures. The downside is that the motion sensor and camera will not be well integrated visually.

  2. Replace my dumb fixtures with ones that have dual bright built in. It's easy to do, and I could even keep the HA Automation I have setup now, but again the camera setup is not going to integrate well visually. I'm also concerned that three motion sensors controlling three lights will cause trouble for the camera (or each other) because they will react to different things and turn themselves on and off independently.

  3. Replace my dumb fixtures with smarter ones. In the center position I'd use one that has an integrated motion sensor and camera. This Reolink seems like it would work pretty well. However RL doesn't make any fixtures that match it, which means my center fixture would look different than the other two.

I may just have to deal with mismatched fixtures but does anyone have any suggestions? Am I missing an option?

top 9 comments
sorted by: hot top controversial new old
[–] gazoinksboe@lemmy.world 3 points 1 year ago (1 children)

The Hue motion sensors are great and can run on Zigbee in lieu of the Hue bridge. I just transitioned my setup to Zigbee2MQTT after hearing their future account requirement and am very happy with the results. Same can be said for their light bulbs for that matter. I have multiple Reolink cameras and love them. You get a lot of bang for your buck and I send all the data to an FTP server so no cloud required.

[–] Buelldozer@lemmy.today 1 points 1 year ago* (last edited 1 year ago) (1 children)

I've heard that the Hue bulbs lose some functionality or control when you transition them over to Zigbee. Can you comment on that?

I'm currently all Z-Wave and I'd prefer to keep it that way. There's nothing wrong with Zigbee I just settled on Z-Wave in the beginning and it's my opinion that the simpler the setup the more reliable it will be; that's why whatever camera(s) I end up with will be PoE. Less protocols, less interfaces, less problems. :)

Reolink's integration with HA and willingness to play nice with Local NVRs is precisely why they are the top of my list for cameras so I'm glad to hear that you've had good luck with them!

[–] gazoinksboe@lemmy.world 1 points 1 year ago

To be honest, I don’t do anything super special with my Hue bulbs but after adjusting the transition period, I can barely notice any difference, except that they respond more quickly and consistently on Zigbee2MQTT. Anything in particular you’re curious about?

[–] ThorAlex@infosec.pub 2 points 1 year ago (1 children)

I use the brightest ikea smart bulbs in mine, I just leave the switches on (they are on three separate swithches in various locations) and control everything in home assistant. Motion sensors are phillips hue outdoor sensors, they work well and double as my outdoor temperature sensors and light sensors. I'd mount the camera and sensor up under the roof, that makes them less prominent and puts them out of easy reach of anyone with bad intentions.

That reolink camera is fucking ugly! No way I'd put that on my wall...

[–] Buelldozer@lemmy.today 1 points 1 year ago (1 children)

Fair comment. I'll skip the Hue sensor though because off their recent shenanigans. What do you use for a camera?

[–] ThorAlex@infosec.pub 2 points 1 year ago* (last edited 1 year ago) (1 children)

I don't have a camera, no need for one.

Guess I'll have to look into what phillips has been up to... Edit: The usual idiotic cloud crap i see... Good thing we are on the home assistant forum, where not needing the stupid hubs is half the point ;)

[–] Buelldozer@lemmy.today 2 points 1 year ago

I punted my SmartThings hub earlier this year and am now "hub free". It's going to stay that way too because I don't trust any of these companies to leave my things and data alone.

[–] rappo@lemmy.world 1 points 1 year ago* (last edited 1 year ago) (1 children)

I have something similar to this with my kitchen setup: I have two motion sensors on either end of the island. I have 2 "bright" light fixtures (hooked up via Zooz smart switches -- these can be dimmable) and one middle light fixture (smart bulb with the switch left on because the switch is in an awkward spot that I never use anyway).

If motion is triggered and it's between 5pm - 11pm, turn on all 3. If it's between 11-4am, just use the dim light. And then after X minutes of inactivity, kill the lights. You could easily add in brightness levels and fades.

I used to have it set to factor in the lesser of sunset or a helper I created ("is it cloudy?") that read the lux value of my weather station, but in the end I just liked the predictably of set times.

All that to say it would be no problem for you to add dimming based on motion + time of day. Grab the Zooz Dimmer and replace your switches with that and grab whatever regular dimmable light fixtures your wife likes. In your automation set your lights to go on at full brightness during sunset, dim at a specific time, then have it adjust brightness when motion is triggered, and then back to the dim setting after a delay.

You can also set a transition time, so lights on at sunset, transition from 100% to 30% over 3 hours, etc.

Another suggestion: with the HA app on your phone, use that to detect if you're coming home and turn the lights on full for a few minutes as you pull in.

[–] Buelldozer@lemmy.today 2 points 1 year ago

Thank you for the suggestions. I've decided that matching fixtures are what's most important to me so I'll be going with Option 1, basically what you just described.